TAGS01 3-Axis Gyro System 4.8 - 8.5V

Please note this product is specifically designed for flybarless helicopters. It cannot be used on a traditional flybar helicopter.

Characteristics

A new era of FBL control with the JR 3 axis Gyro system

• MEMS 3 Axis Gyro Sensor Control
  The TAGS01 utilizes an advanced control algorithm with a wide dynamic range. This allows unmatched hovering stability combined with extreme maneuverability during 3D flight.
• Direct Setup Method
  The basic settings can be intuitively carried out using only the switches and dials, which are incorporated separately for each function in the control unit.
• MEMS Sensor
  Each axis utilizes an advanced control algorithm with a wide dynamic range.
• Digital Filter
  A 32 bit high speed CPU reduces the effects of vibration by digitally processing all information from the sensors, to achieve very stable flying characteristics.
• Swash Mix Scan Function
  The CCPM settings in the transmitter are recognized by the gyro during calibration. The CCPM settings are not changed during installation of the TAGS01.
• New Function: Pirouette Compensation
  Pirouette Compensation operates effectively at all pirouette speeds, adding stability and precision to all phases of flight.
• New Function: E-ring limiter
  During 3D maneuvers, when extreme aileron and elevator controls are combined, the E-ring function limits servo movement to avoid binding (jamming) of the swash plate. This eliminates damage to servos or rotor head linkages.
• G-Tune for TAGS01: Dedicated software and USB interface cable
  It is possible to connect the TAGS01 to a PC for fine tuning and access to additional functionality. An additional dedicated USB interface cable and software will be required.

Specifications

[Gyro Control Unit /TAGS01-A] Dimensions: 37mm x 11.5mm x 5mm Weight: 21g
[Gyro Sensor Unit /TAGS01-S] Dimensions: 27mm diameter x10mm Weight: 14g

• Direct Setup Method
• Swash Mix Scan Function
• Reverse Switch
• Gain Adjust: Aileron, Elevator, Rudder

Items Included:

• Gyro Control Unit / TAGS01-A: (1)
• Gyro Sensor Unit / TAGS01-S: (1)
• Sensor Unit Extension Cable: (1)
• Lead Harness B: (5)
• Dial Adjusting Screwdriver: (1)
• Double-sided Tape for Fixing Sensor Unit: (3)
• Sensor Angle Changing Housing (1)
• Operation Manual: (1)
• TAGS01 Stickers: (1)

INFORMATION

[CAUTION]
Note that analog servos cannot be used with the TAGS01. We highly recommend the following servos, or other JR DS or MP series high performance helicopter servos.

[Precautions]
When using a 2-cell Li-Po battery as a power source, ensure your servos support this voltage (JR HV servos), or use a regulator to supply a voltage compatible with your servos (for example, the JR REG015 or equivalent).
If using high performance servos, please carefully consider your choice of power supply with regard to capacity and discharge capabilities.
If the receiver and servos are being powered from an electronic speed controller using a BEC system, please take care that the BEC is of sufficient current supply capacity.

Suggested Swash Servos

• 50/90 Swash servos
  [4.8V] DS8915 / DS8355 / DS8325 / DS8305 / FBL-DS01
  [7.4V] DS8925HV
• EP500/550 Class Tail Servos
  [4.8V] MP30S / MP30T / MP30G / DS3500 / FBL-DS11

Suggested Tail Servos

• 50/90 Class Tail Servos
  [4.8V] MP80G / DS8900G / DS8400G (50 class only)
  [4.8V-7.4V] MP82GWV / MPH83GWV
• EP500/550 Class Tail Servos
  [4.8V] MP30G / DS3500G

Supported Servos

• [4.8V] MP70A / MP70

Optional Accessories

[02612] (G-TUNE ADAPTER CABLE) Dedicated USA Interface cable for the TAGS01
[04639] Lead harness B 100mm
[04640] Lead harness B 50mm
[05283] Double sided tape for Gyro control sensor unit (TAGS01)

The G-Tune software and interface cable allow fine tuning of all TAGS01 parameters, as well as access to additional functions. Just connect the TAGS01 to your PC using the included interface cable and you are ready to go.
 

• Gain Monitor: Confirmation of the gain value set in the transmitter
• Dead band setting: Setting the response dead band.
• System upgrade: Upgrade your TAGS01 firmware
• System reset: Initialize the TAGS01 to factory defaults
   

Triple Axis Gyro System Parameter Editor GTUNE

NOTE: This product allows access to free firmware upgrades just download the latest firmware from JR PROPO's web site.