Bitte wählen Sie Ihre Währung:
Suche
Bitte wählen Sie Ihr Land: Deutschland England
Warenkorb [Öffnen]  Zeige mehr
0 Produkte
Specials
Suche
 
Hersteller
 

Wählen Sie einen Lieferanten aus der Liste
You pay with
paypal Vorkasse
   
Produkt Informationen
Vorheriger Arikel Artikel?2?von?5 N?chster Artikel
der Kategorie  
XBUS TO DJI/SBUS SIGNAL CONVERTER
XBUS TO DJI/SBUS SIGNAL CONVERTER
Delivery expected:
  Delivery expected
Artikelnummer: ELE004
Preis: 32,50 €
[inkl. 19% MwSt zzgl. Versandkosten]

Menge:   

XBus (Input) to DJI/S.Bus (Output) Signal Converter Module.

This module enables you to use your JR Propo DMSS XBus radio with DJI and other Futaba S.Bus compatible products.

You can use any XBus compatible receiver. Connect the receiver to the converter module using a male to male patch lead. Ensure that the polarity is correct, ground, brown or black wire, should be at the bottom of the converter board. A second male to male patch lead will be required to connect the converter module to the SBus input of the device.

Hersteller/Manufacturer
SH Modelltechnik

Adresse/Address
SH Modelltechnik (Inh.: Kerstin Helmling), Speckweg 130, 68305 Mannheim

Kontakt/Contact
info@shmodelltechnik.com

THANK YOU FOR PURCHASING THIS CONVERTER MODULE.
This module will allow you to fly your JR Ninja 400 orother JR XBus compatible units such as the JR TAGS Minion Spektrum radio. You will need two DSMX satellites with their connecting leads. Note that even if you are usinga DSM2 radio you will still need to use DSMX satellites. DSM2 satellites will not work with this converter.

Connect the two satellite units to the converter module,and then connect the converter module to the Ninja control board using the male to male lead supplied with the Ninja kit. Double check that you have connected the lead in the correc torientation ground (Brownwire) should be towards the outside edge of the converter module.

Use a blank model memory on your transmitter,set the model type to Helicopter and configure the radio as described in the Ninja manual.

Double check using the servo monitor tha t'Hold' gives you-150%on the throttle.Connect the two pin bind plug to the converter module and power up the Ninja.Note that it is recommended that the props are not attached to the motors whilst performing this operation. The light on the converter module will blink orange and the satellites will enter bind mode.Ensure that you have hold mode activated and throttle at zero on the transmitter,then bind your TX using the correct procedure for the specific model.

At the end of the bind process the light onthe converter module will change from flashing orange to solid green. This signifies that the bind is complete and the converter modulei s receiving information from your transmitter. Please note that  the failsafe values are set during this binding process,so it is important that hold be activated when bind completes. Should you change any of the throttle setup or hold setup you are advised to bind again to ensure correct failsafe operation.

If using this converter module with a JRTAGS Mini with adapter lead connect the two satellite units to the converter module, and then connect the converter module to the TAG Mini adapter lead. Double check that you have connected the lead in the correct orientation ground (brownwire) should be towards the outside edge of the converter module.

The light on the converter module provides feedback as to the operating condition of the converter.

The following four indications are possible:

1. Flashing Orange-the converter module is waiting for the satellites to bind.

2. Solid Red-the convert has powered up but has not yet seen any valid signal from the satellite.

3. Solid Green-the converter is receiving good data from the transmitter and sending it to the Ninja contro lunit.

4. Flashing Red-the converter is in the failsafe condition and is sending the pre-programmed failsafe  values to the Ninja control unit.

WARNUNG

RC models are no toys. For children under 14 years of age onlly under adult supervision.

Alle Smartphone Infos:

Jetzt einfach scannen und los. Alle Smartphone Infos auf einen Blick.

JR-Propo Deutschland Kunden kauften auch

DSMX TO XBUS SIGNAL CONVERTER
DSMX TO XBUS SIGNAL CONVERTER
26,90 €
[inkl. 19% MwSt zzgl. Versandkosten]
DMSS Telemetry Adapter TLS1-ADP
DMSS Telemetry Adapter TLS1-ADP
27,50 €
[inkl. 19% MwSt zzgl. Versandkosten]
Stick Shaft 28X
Stick Shaft 28X
9,70 €
[inkl. 19% MwSt zzgl. Versandkosten]
LCD Protective Film (H)  For 28X
LCD Protective Film (H) For 28X
14,80 €
[inkl. 19% MwSt zzgl. Versandkosten]
XB1-HB5  XBus dedicated Hub (5 ports)
XB1-HB5 XBus dedicated Hub (5 ports)
28,50 €
[inkl. 19% MwSt zzgl. Versandkosten]
XB1-CV4 PWM Converter (4 ports type) for XBus
XB1-CV4 PWM Converter (4 ports type) for XBus
59,90 €
[inkl. 19% MwSt zzgl. Versandkosten]
 

Zuletzt angesehene Artikel

RG812BX 8-Channel Rx with XBus (Antenna Diversity Model)
RG812BX 8-Channel Rx with XBus (Antenna Diversity Model)
159,90 €
[inkl. 19% MwSt zzgl. Versandkosten]
Mein Konto
Meine Bestellungen
Meine Rechnungen
AGB
Widerrufsrecht
Datenschutz
Versandkosten
Zahlungsarten
Kontakt
Impressum

(C) 2013 HBSO GmbH
Alle Rechte vorbehalten
Alle Preise inkl. MwSt. zzgl. Versandkosten 

 

Fehler auf der Homepage, Liefertermine und/oder Preisänderungen sind jederzeit vorbehalten!

Shopsystem u. Shopsoftware von hbso.de